Cable Drums and Container Loading: A Buyer's Guide to Export Packing
News Details
Why packing shows up later as a claim
Cable is one of the densest products that moves in a general container. A drum that looks like it fills a third of the floor can already be at the weight limit. Buyers who plan a shipment by volume alone usually find out at the port, when the container is over weight, or at site, when the forklift cannot lift the reel.
Packing is also where most transit damage starts. A drum that collapses, rolls, or loses winding tension takes the jacket with it. The cable inside may be perfectly made and still be rejected on arrival, because a crushed sheath is a rejected delivery.
This guide covers the decisions a buyer actually controls: drum type, drum size, length per drum, how many drums fit, wood treatment, lashing, and what to write on the purchase order so the packing matches the site.
Three drum types and what each one is for
| Drum type | Cost | Strength | Typical use |
| Wooden | Lowest | Moderate, needs dry storage | LV cable, control cable, small sizes, short sea routes |
| Steel-wooden (composite) | Middle | Good, resists handling impact | Standard export packing for LV and MV power cable |
| Steel | Highest | Highest, keeps shape under load | Heavy MV and HV cable, large conductor sizes, long storage |
Two practical notes. First, wooden drums are solid wood packaging, which brings phytosanitary rules into play. Second, a wooden drum absorbs moisture. On a route with high humidity or a long wait at site, the drum can swell or grow mould against the sheath.
For cable above roughly 2 tonnes per drum, composite or steel is the safer default. The difference in price is small next to the cost of a rejected reel.
Reading drum size correctly
Drum size is normally written as PN plus a number, where the number is the flange diameter in millimetres. PN 1600 means a 1,600 mm flange, not a 1,600 mm width. Buyers who read it as width order drums that will not fit through the container door.
| Drum size | Flange diameter | Typical max cable weight | Typical duty |
| PN 1000 | 1,000 mm | Up to 1.0 t | Small LV and control cable |
| PN 1200 | 1,200 mm | Up to 1.5 t | LV power cable, ABC |
| PN 1400 | 1,400 mm | Up to 2.0 t | Standard LV power cable |
| PN 1600 | 1,600 mm | Up to 2.5 t | Armoured LV, light MV |
| PN 1800 | 1,800 mm | Up to 3.0 t | MV cable, heavy copper |
| PN 2000 | 2,000 mm | Up to 4.0 t | Heavy MV power cable |
| PN 2200 | 2,200 mm | Up to 5.0 t | Large MV, long lengths |
| PN 2500 and above | 2,500 mm and above | Up to 8 t or more, steel only | HV and special projects, often break bulk |
Treat these figures as planning guidance and confirm the actual capacity with the factory. Capacity depends on the drum build, not only on the flange size.
Working out net weight per drum
Drum weight is arithmetic, not guesswork. The sequence is:
- Take the mass per metre from the datasheet for the exact construction ordered.
- Multiply by the length wound on the drum.
- Add drum tare. A PN 1600 wooden drum is typically 120 to 180 kg, a composite drum 200 to 300 kg, a steel drum 350 to 500 kg.
- Add packing weight, then use gross weight for freight and for the crane rating at site.
Worked example. A 4 core 35 mm² copper XLPE cable with PVC sheath comes out near 1.9 kg per metre. On a 1,000 m length that is 1,900 kg of cable. Add a composite drum at 250 kg and packing at 50 kg, and the drum ships at about 2.2 tonnes gross. That fits a PN 1600 composite drum, and it tells the site to have a 2.5 tonne lift available.
Two habits keep the numbers honest. Use the datasheet figure for the ordered construction, not a family average, because copper content changes weight far more than diameter suggests. And confirm the length actually wound, because drums are rarely filled to theoretical capacity.
How many drums fit in a 40HQ
A 40HQ has about 12.03 m of internal length, 2.35 m of width and 2.69 m of height. The payload ceiling on paper is around 26 to 28 tonnes, but road limits at both ends usually decide the real figure, so plan against roughly 24 to 26 tonnes for a 40 foot container.
The method has three checks, in this order:
- Floor count. Drums ship standing on the flange. Footprint is flange diameter times traverse width. Usable floor is length times width times 0.9 for gaps and bracing.
- Height check. A drum standing on the flange needs its diameter to clear the internal height. Above about 2.2 m diameter, a standard container is no longer comfortable.
- Weight check. Multiply drums by gross weight and compare with the payload you can actually move at destination.
Worked example. PN 1600 drums, 1.6 m flange, 0.9 m width, 2.2 tonnes gross. Footprint is 1.44 m². Usable floor is 12.03 × 2.35 × 0.9, about 25.4 m², which suggests 17 drums on the floor. But 17 × 2.2 tonnes is 37 tonnes, well past the limit. The container is weight limited to about 12 drums, roughly 26 tonnes and, at 1 km per drum, 12 km of cable.
This is the normal result for power cable. Volume stops mattering once drums are large, and the loading plan becomes a weight plan. For mixed cross sections, run the calculation per drum type and then combine, because one heavy drum can sit next to three light ones without exceeding either the floor or the axle limit.
ISPM 15: the stamp that decides whether the container is accepted
Solid wood packaging, including drum battens, pallets and dunnage, must be heat treated or fumigated and marked under ISPM 15, the FAO plant health standard. Heat treatment means the core of the wood reaches 56 °C for at least 30 minutes. The treated wood carries the IPPC mark with the country code, producer code and treatment code.
Processed wood such as plywood is exempt. Steel drums are exempt. Untreated solid wood is not a small problem: the container can be held, re-treated, or returned at the importer's cost, and the delay can outlast the project window.
If your drum specification says wooden, put the ISPM 15 requirement in the purchase order and ask for photographs of the marks before loading. It is a two minute check that has stopped a lot of shipments.
Securing the load
Drums roll. That single fact drives the whole lashing method, and it is the part most often done badly on cheap packing.
- Stand drums on the flange and chock both sides so the drum cannot rotate.
- Brace rows against the container walls with lumber, and fill gaps so nothing can shift into a void in heavy weather.
- Strap over the flanges to the container lashing points, not around the cable.
- Wind under tension and brake properly. A slipping brake lets outer layers loosen and the cable birdcages, which damages the jacket and sometimes the conductor.
- Seal both ends with a cap or heat-shrink boot. Moisture enters at the ends faster than through the sheath.
The IMO, ILO and UNECE publish the CTU Code for packing cargo transport units. It is the reference to cite if a forwarder or a surveyor questions the lashing plan.
Marking, documents and the metre count
Each drum should carry the buyer name, project or PO number, cable designation, size, length, gross and net weight, drum number, and a rolling direction arrow. The sheath itself should be marked at every metre with the manufacturer, standard, type and year, which is what allows a length check at site.
The document set that avoids arguments on arrival: a drum level packing list, the mill certificate for the conductor rod, a routine test report for each drum, the bill of lading, certificate of origin, and cargo insurance. If the project needs third-party inspection, the inspection release note belongs in the same folder, because customs and the site store both ask for it.
Incoterms and who pays for the drum
Drum cost is usually inside the unit price, but not always. Some suppliers quote cable only and charge drums separately, which changes the landed cost comparison between two suppliers. Ask the question in writing.
Under FOB, the buyer pays for lashing, dunnage and loading beyond what the seller includes. Under CIF or DAP, those costs sit with the seller, but destination unloading is still the buyer's risk. A two tonne drum needs a forklift with the right rating or a crane, and a port that charges by the hour turns slow unloading into demurrage.
Returnable steel drums exist but are rarely economic on export lanes. Assume the drum is consumed, and price it as packaging.
What to put on the enquiry
- Maximum drum weight the site crane or forklift can handle.
- Maximum flange diameter that fits the site access and the container door.
- Length per drum you want, and whether short lengths are acceptable on the last drum.
- Drum material, and whether ISPM 15 marking is required.
- Marking text and any buyer tag or QR requirement.
- Whether you want a loading plan drawing before shipment.
- Destination unloading equipment and any road weight limit.
Seven lines in the enquiry remove most of the disputes that otherwise surface three weeks after the vessel sails. For the wider buying sequence behind the order, read our electrical cable and wire sourcing guide. Freight and packing also sit inside the cost discussion in the seven factors behind bulk cable prices.
Frequently asked questions
How many metres fit on one drum?
It depends on conductor size and drum capacity, not on a standard figure. A light 4 core 35 mm² cable can run 1,000 m on a PN 1600 drum, while a heavy 4 core 240 mm² cable often ships 250 to 500 m on a much larger steel drum. Always confirm the wound length against the drum weight.
Can I get a loading plan before shipment?
Yes, and you should ask for one on any order above a single container. A drawing that shows drum positions, weights and lashing points is the cheapest way to catch a weight problem while the cable is still in the factory.
Are wooden drums accepted in the EU and US?
Yes, if the wood is ISPM 15 treated and marked. Untreated solid wood packaging is the issue, not wood as a material.
Is the drum included in the cable price?
Usually, for standard export packing. Ask explicitly, because a quote that excludes drums is not comparable with one that includes them.
What damages cable in transit most often?
Collapsed or rolling drums, and loosened winding. Both come from packing and lashing, not from the cable itself.
Standards referenced in this guide
- ISPM 15, regulation of wood packaging material in international trade, issued by the IPPC under FAO.
- CTU Code, Code of Practice for Packing of Cargo Transport Units, issued by IMO, ILO and UNECE.
- IEC 60502-1, extruded insulation power cables up to 1 kV, issued by the International Electrotechnical Commission.
- IEC 60228, conductors in insulated cables, issued by the International Electrotechnical Commission.
If you are planning a shipment with mixed drum sizes or a site with a tight crane limit, send us the cable schedule and the destination. We will return a packing and loading proposal against your handling equipment, including drum weights per line.