Blogs /
Understanding Cable Designations: YJV22, NYY, N2XH, and H07RN-F

Understanding Cable Designations: YJV22, NYY, N2XH, and H07RN-F

YJV22, NYY, N2XH and H07RN-F describe the same job in four standards. Decode the letters, read the cross-reference table, and see where equivalence stops before you substitute.

News Details

One cable, four names

A copper conductor, XLPE insulated, PVC sheathed, 0.6/1 kV power cable is sold as YJV in China, N2XY in Germany, Cu/XLPE/PVC in a British specification, and something close to XHHW-2 in a North American one. The four names describe roughly the same job and not the same product.

That gap causes real money. A buyer substitutes on the strength of the code, the cable arrives dimensionally different, and the inspector rejects it against a standard nobody compared.

This guide decodes the codes most often seen in export enquiries, then shows where equivalence stops.

Decoding the GB and Chinese export code

The GB designation is built from position, not words. Each position says something about one layer.

Letter or number Meaning
YJ Cross-linked polyethylene insulation (XLPE)
V PVC insulation or sheath, depending on position
L Aluminium conductor. Copper is the default and is not written
T Copper, written only when clarity is needed
22 Steel tape armour with PVC outer sheath
23 Steel tape armour with PE outer sheath
32 Thin steel wire armour with PVC outer sheath
33 Thin steel wire armour with PE outer sheath
42 Thick steel wire armour with PVC outer sheath
WDZ Low smoke, halogen-free, flame retardant
NH Fire resistant, normally mica tape on the conductor
B Single core building wire, fixed wiring
K Control cable
R Flexible conductor
P Braid or tape screen

Read left to right: insulation, conductor, armour, sheath. The first letter group is insulation, the armour digit comes last, and the outer sheath is implied by the armour code.

Five worked examples

Designation Construction Typical use
YJV Cu, XLPE insulation, PVC sheath, unarmoured Indoor trays, cable ladders, protected routes
YJLV22 Al, XLPE insulation, steel tape armour, PVC sheath Direct burial, MV distribution
YJV32 3x185 Cu, XLPE, thin steel wire armour, PVC sheath Routes with tensile load or risk of impact
VV Cu, PVC insulation, PVC sheath LV fixed wiring, 70 °C conductor
WDZA-YJY Cu, XLPE, halogen-free sheath, class A flame retardant Metro, tunnel, hospital, public buildings

The size suffix matters as much as the letters. In 3x185, the first number is the core count and the second is the cross section in square millimetres. A 3x185 does not mean three cores of 185 mm² total; it means three cores of 185 mm² each.

The European VDE code

German and much of continental European practice uses a letter system that reads differently.

Code Construction Notes
NYY Cu, PVC insulation, PVC sheath 0.6/1 kV, unarmoured, the land cable baseline
NAYY Al, PVC insulation, PVC sheath Aluminium version of NYY
N2XY Cu, XLPE insulation, PVC sheath Higher temperature and current than NYY
NA2XY Al, XLPE insulation, PVC sheath Aluminium XLPE distribution
N2XH Cu, XLPE insulation, halogen-free sheath The common European LSZH construction
NYCWY Cu, PVC, concentric copper wave screen Where an earth screen must be continuous
NHXHX FE180 Fire resistant, halogen-free Circuit integrity for 180 minutes under DIN 4102-12

The N is a standard cable marker rather than a material. Y is PVC, 2X is XLPE, H is halogen-free. Once that mapping clicks, most European codes become readable.

British constructions

British specifications rarely use a code. They spell out the construction, and the standard number does the rest.

  • Cu/XLPE/PVC/SWA/PVC to BS 5467, the workhorse armoured distribution cable.
  • Cu/XLPE/LSZH/SWA/LSZH to BS 6724, the same cable with a halogen-free sheath for enclosed and public spaces.
  • Cu/XLPE/PVC unarmoured to BS 7211 for tray and conduit routes.
  • 6491X single core PVC building wire to BS 6004.
  • BS 6387 CWZ is a fire resistance category rather than a cable type, and it is often quoted alongside BS 7846 fire resistant cable.

The point to hold on to is that BS 5467 armoured means steel wire armour. A GB 22 construction is steel tape. They are not the same mechanical protection, and a British engineer will notice.

North American types

North America names cable by insulation and application rather than by layer sequence.

  • XHHW-2: XLPE insulation, rated 90 °C in wet and dry locations, widely used in conduit and trays.
  • THHN/THWN-2: PVC insulation with a nylon jacket, 90 °C dry, 75 °C wet.
  • RHW-2 / USE-2: rubber or XLPE, underground service and direct burial.
  • MV-90 / MV-105: medium voltage cable at 90 °C or 105 °C conductor rating.
  • TC-ER: tray cable with exposed run permission.
  • Type W and G-GC: heavy duty trailing cable for mining and mobile equipment.

Sizes are AWG and kcmil. A 4/0 AWG is about 107 mm², and 250 kcmil is about 127 mm². Anyone converting by eye gets the size wrong by a step.

Cross-reference table

Use this as a starting point for a conversation, not as a substitution authority.

VDEIEC base
Construction GB British
Cu, PVC, PVC, unarmouredVVNYYCu/PVC/PVCIEC 60502-1 Al, PVC, PVC, unarmouredVLVNAYYAl/PVC/PVCIEC 60502-1 Cu, XLPE, PVC, unarmouredYJVN2XYCu/XLPE/PVC, BS 7211IEC 60502-1 Al, XLPE, PVC, unarmouredYJLVNA2XYAl/XLPE/PVCIEC 60502-1 Cu, XLPE, steel tape armour, PVCYJV22Rare in VDE rangeCu/XLPE/STA/PVCIEC 60502-1 Cu, XLPE, steel wire armour, PVCYJV32 or YJV42Rare in VDE range Cu/XLPE/SWA/PVC, BS 5467 IEC 60502-1 Cu, XLPE, halogen-free WDZ-YJY N2XH Cu/XLPE/LSZH, BS 8573 IEC 60502-1 Cu, XLPE, SWA, halogen-free WDZ-YJY32 Rare in VDE range Cu/XLPE/LSZH/SWA/LSZH, BS 6724 IEC 60502-1
If you are comparing offers on a

XLPE insulated power cable

, put the standard and the construction on the same line of the comparison table. A price comparison across two different standards is not a comparison. Where equivalence breaks Five differences survive every tidy cross-reference sheet. Sheath and insulation thickness. Each national standard sets its own minimums. A cable that meets IEC can be thinner than the British equivalent, and an inspector measuring to BS will reject it. Armour type. Tape and wire armour behave differently under tensile load and under crush. They are not interchangeable even when the current rating matches. Conductor class and strand count. A Class 2 stranded conductor and a Class 5 flexible conductor of the same size terminate differently and bend differently. Temperature rating. PVC at 70 °C and XLPE at 90 °C change the derated current for the same copper. Substituting one for the other changes the protection setting. Approval route. A UL listing, a VDE certificate, a KEMA type test and a CPR declaration of performance answer different legal questions. An inspector at site accepts the one named in the specification. How to write a spec that cannot be substituted Three lines remove most of the risk:
  • Name the construction in full: conductor material and class, insulation, armour, sheath, voltage class.
  • Name the standard with its edition, and name the test standards separately where fire performance is claimed.
  • Say what may be offered as an alternative, and who approves it. Silence is read as permission.
  • A fourth line helps in practice: ask the supplier to state, on the quotation, the standard to which the cable will be manufactured and the type test certificate that supports it. A supplier who cannot fill both blanks has not read the enquiry. For the buying steps behind the code, our XLPE sourcing guide walks through specification, standards and documentation in order. Frequently asked questions Is YJV the same as N2XY? Both are copper, XLPE insulated, PVC sheathed, 0.6/1 kV. They are made to different standards, so dimensions and test evidence differ. Treat them as similar, not identical. What does the 22 in YJV22 mean? Steel tape armour with a PVC outer sheath. The 32 and 42 variants use thin and thick steel wire armour instead. Can I use NYY where the drawing says YJV? No. NYY has PVC insulation rated at 70 °C; YJV has XLPE at 90 °C. The current rating and the protection setting both change. Is N2XH the same as WDZ-YJY? Both are halogen-free XLPE constructions. Flame class, smoke limits and sheath compound still need to be compared line by line. How do I convert mm² to AWG? Use the standard conversion table rather than a factor. Rounding by eye usually lands one size small, which is the wrong direction for a safety margin. Standards referenced in this guide
  • IEC 60502-1 and IEC 60502-2, extruded insulation power cables, issued by the International Electrotechnical Commission.
  • IEC 60228, conductors in insulated cables, issued by the International Electrotechnical Commission.
  • GB/T 12706, rated voltages up to and including 35 kV extruded insulation power cables, issued in China.
  • DIN VDE 0276 and the HD 603 series, power cables up to 3.3 kV, issued by VDE and CENELEC.
  • BS 5467, BS 6724, BS 7211 and BS 6004, issued by the British Standards Institution.
  • UL 44 and UL 854, thermoset and thermoplastic insulated wire, issued by UL Standards.
  • If a yard drawing reaches you as an unfamiliar designation, send it over with the standard reference. We will map it to a construction we build in PVC insulated, armoured or halogen-free form, and say plainly where equivalence stops.
    Share to:
    facebook
    line
    Whatsapp
    Pinterest
    Tumblr
    Linkedin