Routine, Sample & Type Tests: Cable Pre-Shipment Verification Guide
News Details
Three test families, three different jobs
Cable testing is often discussed as if it were a single activity. In IEC terms it is three separate test families, and each answers a different question.
- Routine tests ask whether this particular length is sound. They are run on every drum.
- Sample tests ask whether the production batch was built to the drawing. They are run on a sample of drums.
- Type tests ask whether the design works at all. They are run once, on a representative sample, and are not repeated per order.
Buyers who ask only for a test report often receive the first and assume they have the third. That is where the surprise comes later, when a joint fails or a sheath measures under the minimum. Knowing which document proves which claim is the whole skill.
Routine tests: every drum, every length
Routine tests are the ones you can demand for the actual goods on the vessel. Under IEC 60502-1 and 60502-2 they cover three things.
| Test | What it proves | Typical requirement |
| Conductor DC resistance | Copper or aluminium cross section and purity | At or below the IEC 60228 value for the class and size, corrected to 20 °C |
| Voltage test | Insulation withstands service voltage with margin | Applied to every length for a defined duration, no breakdown |
| Partial discharge | No voids or contamination in the insulation of MV cable | Measured at elevated voltage, discharge below the specified limit |
The conductor resistance test is the one that catches the most fraud, because it does not care how the cable looks. A conductor can measure correctly at the calliper and still fail resistance if it is recycled copper, copper clad aluminium, or drawn from a smaller rod. Resistance is the honest number.
Partial discharge matters for medium voltage. A reading of a few picocoulombs on a 12/20 kV cable is normal. A reading that climbs with voltage points to a void or a contaminated compound, and that cable will fail in service even though it passed the voltage test.
Sample tests: the batch, not the drum
Sample tests destroy the sample, which is why they cannot run on every length. They cover the physical build:
- Conductor examination, including wire count and direction of lay
- Insulation thickness at several points, and the minimum, not only the average
- Sheath thickness, same rule
- Overall diameter and ovality
- Tensile strength and elongation of insulation and sheath, before and after ageing
- Hot set test for XLPE, which confirms the polymer is genuinely cross-linked
- Shrinkage, water absorption, and carbon black content where the standard requires them
The hot set test is worth singling out. It distinguishes cross-linked polyethylene from a compound that was merely extruded and never cured. A cable that fails hot set will deform at operating temperature, and no routine test will warn you.
Type tests: the design, once
Type tests prove the construction, not the batch. For power cable they include the electrical tests that take time: partial discharge at elevated voltage, dielectric loss, heating cycle, and impulse voltage for MV and above.
Where the cable claims fire performance, type tests also cover flame propagation, smoke density and acid gas emission. Those are the tests behind a CPR class or a BS 6387 category, and they must come from an accredited laboratory, not from the factory's own bench.
Three questions turn a type test certificate into evidence:
- Which laboratory issued it, and is that laboratory accredited for the specific test?
- Which edition of the standard was applied, and does it match the edition in your specification?
- Does the tested construction match what you are buying, including conductor class, armour, and sheath compound?
Most buyers also apply an age rule, commonly five years. That is a commercial preference rather than a rule in the standard, but it is a reasonable one, because compounds and processes change.
What a routine test report should contain
A report that lists only pass and fail is not much use. Insist on:
- Drum number, length and cable designation for each line
- Measured resistance per kilometre, with the temperature correction applied
- Voltage test level and duration
- Partial discharge reading in picocoulombs where applicable
- Date, shift, and the name of the tester
- Reference to the type test certificate number for the construction
That last line is what ties the batch to the design. Without it, the two documents are unrelated pieces of paper.
Witnessing a factory acceptance test
A factory acceptance test is not a plant tour. In a well run visit you can cover the essentials in about six hours, and the sequence matters more than the length.
- Start with documents: type test certificate, routine reports for the lot, conductor mill certificate, and the approved drawing.
- Pick drums yourself, at random, from the finished lot. Not from a sample rack.
- Watch the resistance measurement, and check that the ambient temperature is recorded. An uncorrected reading at 35 °C flatters a poor conductor.
- Cut a sample and measure insulation and sheath at the thinnest point, not the average.
- Check the length counter against the drum label, and rewind a short length if the counter looks tampered with.
- Read the sheath marking: manufacturer, standard, type, size, year. A wrong year or a missing standard is a traceability problem.
- Look at the packing: drum condition, end seals, ISPM 15 mark, and whether the drum can survive the lashing plan.
Photograph what you measure. A measurement without a photo is a conversation; a measurement with a photo is a record.
Third-party inspection: scope and sampling
Independent inspection from SGS, Bureau Veritas, TUV, Intertek or Kiwa adds a signature that a factory cannot provide for itself. It is worth the cost when the order is large, the supplier is new, or the project carries liquidated damages.
Scope is where buyers lose value. A pre-shipment inspection that only counts cartons proves nothing about a cable. Specify the technical content:
- Sample selection from the finished lot, with the inspector choosing, not the factory
- Dimensional check on cut samples, thinnest point
- Conductor resistance on at least one drum per size
- Length verification by rewind on a sample
- Marking and packing check against the purchase order
- Container loading supervision, with the loading plan signed
Budget the inspection into the price comparison. On a container of MV cable it is a small fraction of the order, and it is the only line that checks the goods rather than the brochure.
Five gaps that survive most inspections
Length. A drum labelled 1,000 m that holds 970 m is hard to detect and easy to sell. Only a rewind proves it.
Thinnest point. Average thickness can pass while the minimum sits below the standard, usually on one side of an eccentric core.
Temperature correction. Resistance figures quoted without a reference temperature, or corrected with the wrong coefficient for aluminium, are not comparable.
Certificate scope. A type test for a 3 core 185 mm² construction does not cover a single core 400 mm² cable, even from the same family.
Drum count. The packing list says 18 drums, the container holds 17, and the missing one is discovered at site. Count at loading.
Our case note on five red flags in cable quality inspection goes through the field version of these checks, and the sourcing guide sets out where inspection sits in the buying sequence.
Documents that should travel with the container
- Routine test report, one line per drum
- Type test certificate for the construction, from an accredited laboratory
- Dimensional inspection report on cut samples
- Conductor mill certificate
- Packing list with drum numbers, lengths and gross weights
- Third-party inspection release, where appointed
- Declaration of conformity to the ordered standard
Frequently asked questions
Is a routine test report enough to accept a delivery?
No. It proves the length is electrically sound. It says nothing about wall thickness, cross-linking, or whether the design passed type testing. Ask for all three levels.
How often should type tests be repeated?
On a design or material change, and on a commercial cycle that most buyers set at five years. The standard does not set a calendar life for a certificate.
Why do two suppliers quote different test levels for the same cable?
Usually because one is quoting a national standard and the other an IEC equivalent, or because the voltage test duration differs. Compare the standard edition before comparing the number.
Can I witness tests remotely?
Yes. A live video walk-through with the inspector measuring on camera is accepted by many buyers, and costs far less than a site visit. Ask for the raw readings, not only the summary sheet.
Does a third-party inspection replace the FAT?
No, it complements it. The FAT is where you agree the method; the inspection is where the method is applied to your goods.
Standards referenced in this guide
- IEC 60502-1 and IEC 60502-2, extruded insulation power cables, issued by the International Electrotechnical Commission.
- IEC 60228, conductors in insulated cables, issued by the International Electrotechnical Commission.
- IEC 60270, partial discharge measurements, issued by the International Electrotechnical Commission.
- IEC 60332, IEC 60754 and IEC 61034, flame propagation, acid gas and smoke density, issued by the International Electrotechnical Commission.
- ISO/IEC 17025, competence of testing and calibration laboratories, issued by ISO and IEC.
Our XLPE insulated power cable range ships with drum level routine reports and type test certificates on request. If you are writing an inspection clause, send us the draft and we will confirm what the factory can witness and document.